Regency L234-NG User Manual

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4918-667aWARNING: Improper installation, adjustment, alteratio

Regency® L234 Direct Vent Gas Insert10INSTALLATIONTHE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANC

Regency® L234 Direct Vent Gas Insert 11INSTALLATIONCONVERTING FROM 3" & 3" VENTING TO 3" & 2"1) Remove the top plate from

Regency® L234 Direct Vent Gas Insert12INSTALLATIONGAS INSERT AERATION SYSTEMThe burner aeration is factory set but may need adjusting due to either th

Regency® L234 Direct Vent Gas Insert 13INSTALLATIONGAS PIPE PRESSURE TESTINGThe appliance must be isolated from the gas supply piping system by closin

Regency® L234 Direct Vent Gas Insert14INSTALLATIONCONVERSION KIT #536-969 FROM NG TO LPINSTALLATIONLP Conversion Kit Contains:Qty. Part # Descrip

Regency® L234 Direct Vent Gas Insert 15INSTALLATIONINSTALLATION9) Remove burner orifi ce with a 1/2" wrench and discard.10) Install the new LP bu

Regency® L234 Direct Vent Gas Insert16INSTALLATIONOPTIONAL BRICK PANEL INSTALLATION1) Carefully remove the brick panels from the box and unwrap them

Regency® L234 Direct Vent Gas Insert 17INSTALLATIONCONTOUR OR CONTEMPORARY FACEPLATE Faceplate Contents List:1 Faceplate (Contour or Contemporary)1

Regency® L234 Direct Vent Gas Insert18INSTALLATION7) From the right side of the unit connect the black electrode wire to the DC Sparker as shown in d

Regency® L234 Direct Vent Gas Insert 19INSTALLATION13) Tuck the wires completely into the sleeve and place the supplied cable tie to the end of it as

Regency® L234 Direct Vent Gas Insert2REGENCY GAS FIREPLACE INSERTTO THE NEW OWNERCongratulations! You are the owner of a state-of-the-art Gas Insert

Regency® L234 Direct Vent Gas Insert20INSTALLATIONOPTIONAL BACKING PLATE3) Attach the top piece of the backing plate to the faceplate using 5 screws

Regency® L234 Direct Vent Gas Insert 21INSTALLATIONAttach Left & Right Backing Plate to Faceplate7) Align the screw holes on the left and right s

Regency® L234 Direct Vent Gas Insert22INSTALLATIONOPTIONAL HEARTH TRIM1) Open the left and right side faceplate panels. 2) Align the screw holes on

Regency® L234 Direct Vent Gas Insert 23INSTALLATIONLOG SET INSTALLATIONLog kit (Part # 536-930) contains the following pieces: a) 2-711 Rear Log b) 2

Regency® L234 Direct Vent Gas Insert24INSTALLATION5) Fit the left side of log 2-713 into the pin on log 2-714 and rest the right side of the log on t

Regency® L234 Direct Vent Gas Insert 25INSTALLATION7) Place embers on the right side of the burner as shown. 8) Fit log 2-716 into the pin on log

Regency® L234 Direct Vent Gas Insert26INSTALLATIONCompleted Log Set Installation2-7112-7162-715 2-7122-7132-714INSTALLATION

Regency® L234 Direct Vent Gas Insert 27INSTALLATIONWIRING DIAGRAMSThis heater does not require a 120V A.C. supply for operation. However, a 120V A.C.

Regency® L234 Direct Vent Gas Insert28INSTALLATIONINSTALLATIONUse of FPI Remote Control Kit #910-399 or #910-368 is approved for this unit. Use of oth

Regency® L234 Direct Vent Gas Insert 29OPERATIONOPERATING INSTRUCTIONSIMPORTANT: Gas on/off knob cannot be turned from "PILOT" to "OFF&

Regency® L234 Direct Vent Gas Insert 3TABLE OF CONTENTSSAFETY LABELSafety Label ...4REQ

Regency® L234 Direct Vent Gas Insert30OPERATIONOPERATING INSTRUCTIONSCOPY OF LIGHTING INSTRUCTION PLATEAUTOMATIC CONVECTION FAN OPERATIONThe fan oper

Regency® L234 Direct Vent Gas Insert 31MAINTENANCEMAINTENANCE2) Remove the Termination Cap, and shine a fl ashlight down the Vent. Remove any bird nes

Regency® L234 Direct Vent Gas Insert32MAINTENANCEMAINTENANCEFAN REPLACEMENT1) Unplug the power source.2) Open the left and right side faceplate pane

Regency® L234 Direct Vent Gas Insert 33MAINTENANCEMAINTENANCE11) Unplug the fan connector wires.12) Remove the 2 screws that hold the fan bracket in

Regency® L234 Direct Vent Gas Insert34MAINTENANCEMAINTENANCEVALVE REPLACEMENT1) Open the left and right side faceplate panels.2) Remove the bottom l

Regency® L234 Direct Vent Gas Insert 35MAINTENANCEMAINTENANCE13) Remove the rear log tray by undoing the 3 screws.Rear Log Tray Removed14) Remove the

Regency® L234 Direct Vent Gas Insert36PARTS LISTPARTS LISTMAIN ASSEMBLY Part # Description Part # Descriptio

Regency® L234 Direct Vent Gas Insert 37PARTS LISTPARTS LISTFACEPLATE ASSEMBLY Part # Description

Regency® L234 Direct Vent Gas Insert38PARTS LISTPARTS LISTBACKING PLATE & HEARTH TRIM ASSEMBLY Part # Description

Regency® L234 Direct Vent Gas Insert 39WARRANTYRegency Fireplace Products are designed with reliability and simplicity in mind. In addition, our inter

Regency® L234 Direct Vent Gas Insert4INSTALLATIONSAFETY LABELThis is a copy of the labels that accompany each L234 Gas Insert. We have printed a copy

Installer: Please complete the following informationDealer Name & Address: _______________________________________________________________________

Regency® L234 Direct Vent Gas Insert 5INSTALLATIONREQUIREMENTS5.08: Modifications to NFPA-54, Chapter 10(2) Revise 10.8.3 by adding the following addi

Regency® L234 Direct Vent Gas Insert6INSTALLATIONUNIT & FACEPLATE DIMENSIONS

Regency® L234 Direct Vent Gas Insert 7INSTALLATIONINSTALLATIONIMPORTANT MESSAGE SAVE THESE INSTRUCTIONSThe FPI Direct Vent Gas Insert must be installe

Regency® L234 Direct Vent Gas Insert8INSTALLATIONINSTALLATION11) Due to high temperatures, the appliance should be located out of high traffi c areas a

Regency® L234 Direct Vent Gas Insert 9INSTALLATIONINSTALLATIONMINIMUM CLEARANCES TO COMBUSTIBLES Side Walls A 8" (203